Logiccontrols USB Devices Driver

Posted on

Logic Controls hardware is engineered and known worldwide to be very reliable in humid, harsh environments. Used in over 500,000 stations worldwide; quality and pride in engineering is our top priority – and it shows. Intel Android device USB driver, free download. Adds functionality in Windows for management of Android phone and tablet devices with an Intel Atom CPU chip installed. Includes tests and PC download for 32-bit/64-bit systems. When connecting Logic to the USB port and starting the Logic software, the Device Manager may show the device as 'Logic Pro.' This is incorrect, and may cause issues with operation. The solution is to uninstall and reinstall the Logic driver on the PC.

The USB drivers are available on our web site at www.logiccontrols.com. Please download and unzip the driver files before installation. There are two types of driver interface available. If the POS software is only able to access COM port for the pole display, use the virtual COM port interface. Logic Controls (USB) – Windows XP Driver. Click here to download Logic Controls USB Line Display drivers. Install Hardware Driver. DO NOT plug the device in USB port. Download and Extract the above driver to the Desktop; Navigate to:OPOSLD9usb folder, and double-click Setup.exe. Select “Device Name Driver” by clicking the radio and click.

The Logic Controls LD9900 USB device drivers are needed for complete installation of the LD9900 pole display.

There are two types of drivers available. The first uses a specific device name (.LCLD9) to access the pole display directly. If you are using OPOS or if the POS software was tailored to use this device name, refer to the first section below. If the POS software is only able to access COM ports for the pole display, follow the virtual COM port device driver instructions.

Installing the USB drivers with device name .LCLD9.

Controls

Floppy Disk Install

To install the pole display USB drivers from the pole display floppy diskette, perform the following steps:

  1. Connect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  2. Click to select Specific Location, and then click Next.
  3. Insert the LD9900 USB Driver diskette into the floppy disk drive.
  4. Under the Include this location in the search field section, click Browse and click to select A:Win2000.
  5. Click to select driver LCLD9.inf, click Next, and thenclick Finish.
  6. Remove the LD9900 USB Driver diskette.
  7. Right-click My Computer andclick Properties.
    The System Properties window appears.
  8. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  9. Complete the installation by verifying the driver is now appearing in Device Manager correctly. (Figure 1)
    Figure 1 - Correct Device Manager Listing

Floppy Disk Reinstall

To reinstall the pole display USB drivers from the pole display floppy diskette, perform the following steps:

  1. Remove the USB pole display cable from the USB port.
  2. Right-click any unknown items, and then click to select Remove. (Figure 2)
    Figure 2 - Unknown Device
    NOTE: If there are any references to Line Display LD9900, right-click on the listing, and then click Uninstall.
  3. Repeat step 2 until there are no unknown devices in Device Manager.
  4. Reconnect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  5. Click to select Specific Location and click Next.
  6. Insert the LD9900 USB Driver diskette into the floppy disk drive.
  7. Under the Include this location in the search field section, click Browse and click to select A:Win2000.
  8. Click to select driver LCLD9.inf, click Next, and thenclick Finish.
  9. Remove the LD9900 USB Driver diskette.
  10. Click My Computer,andthen click Properties.
    The System Properties window appears.
  11. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  12. Complete the installation by verifying the driver is now appearing in Device Manager correctly. (Figure 1)

Internet Install

To install the pole display USB drivers from the Internet, perform the following steps:

  1. Download the driver file at:www.logiccontrols.com/web/utilities/ld9w2k.zip.
  2. Choose Open from the File Download prompt.
  3. Click File and then click to select Extract All.
    The Extraction Wizard screen loads.
  4. Type C:LCLD9 at the prompt and click Next.
    The Extraction Wizard begins unzipping files.
  5. Click Finish to complete the file extraction.
  6. Connect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  7. Click to select Specific Location and click Next.
  8. Under the Include this location in the search field section, click Browse and click to select C:LCLD9.
  9. Select driver LCLD9.inf, click Next, and then click Finish.
  10. Right-click My Computer andthenclick Properties.
    The System Properties window appears.
  11. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  12. Complete the installation by verifying the driver is now appearing in Device Manager correctly. (Figure 1)

Logiccontrols USB Devices Driver

Internet Reinstall

To reinstall the pole display USB drivers from the Internet, perform the following steps:

  1. Download the driver file at: www.logiccontrols.com/web/utilities/ld9w2k.zip.
  2. Choose Open from the File Download prompt.
  3. Click File and then click to select Extract All.
    The Extraction Wizard screen loads.
  4. Type C:LCLD9 at the prompt and click Next.
    The Extraction Wizard begins unzipping files.
  5. Click Finish to complete the file extraction.
  6. Remove the USB pole display cable from the USB port.
  7. Right-click any unknown items, and then click to select Remove. (Figure 2)
    NOTE: If there are any references to Line Display LD9900, right-click the listing, and then click Uninstall.
  8. Repeat step 2 until there are no unknown devices in Device Manager.
  9. Right-click any unknown items, and then click to select Remove.
  10. Repeat this step until there are no unknown devices left.
  11. Reconnect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  12. Choose Specific Location and click Next.
  13. Under the Include this location in the search field section, click Browse and click to select C:LCLD9.
  14. Select driver LCLD9.inf, click Next,and then click Finish.
  15. Right-click My Computer andclick Properties.
    The System Properties window appears.
  16. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  17. Complete the installation by verifying the driver is now appearing in Device Manager correctly. (Figure 1)

Install the pole display USB drivers (Virtual COM Port).

Floppy Disk Install

To install the pole display USB virtual COM port drivers from the floppy diskette, perform the following steps:

  1. Connect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  2. Click to select Specific Location and click Next.
  3. Insert the LD9900 USB Driver diskette into the floppy disk drive.
  4. Under the Include this location in the search field section, click Browse and click to select A:Win2000.
  5. Click to select driver LD9COM.inf, click Next,and thenclick Finish.
  6. Remove the LD9900 USB Driver diskette.
  7. Right-click My Computer andclick Properties.
    The System Properties window appears.
  8. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  9. Complete the installation by verifying the driver is now appearing correctly in device manager under Ports (COM & LPT), and note the port number.

Floppy Disk Reinstall

To reinstall the pole display USB virtual COM port drivers from the floppy diskette, perform the following steps:

  1. Remove the USB pole display cable from the USB port.
  2. Right-click any unknown items, and then click to select Remove. (Figure 2)
    NOTE: If there are any references to Line Display LD9900, right-click on the listing, and then click Uninstall.
  3. Repeat step 2 until there are no unknown devices in Device Manager.
  4. Reconnect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  5. Click to select Specific Location and click Next.
  6. Insert the LD9900 USB Driver diskette into the floppy disk drive.
  7. Under the Include this location in the search field section, click Browse and click to select A:Win2000.
  8. Click to select driver LD9COM.inf, click Next,and thenclick Finish.
  9. Remove the LD9900 USB Driver diskette.
  10. Right-click My Computer andclick Properties.
    The System Properties window appears.
  11. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  12. Complete the installation by verifying the driver is now appearing correctly in device manager under Ports (COM & LPT) and note the port number.

Internet Install

To install the pole display USB virtual COM port drivers from the Internet, perform the following steps:

Logiccontrols USB Devices Driver
  1. Download the driver file at: www.logiccontrols.com/web/utilities/ld9w2kcom.zip.
  2. Choose Open from the File Download prompt.
  3. Click File and click to select Extract All.
    The Extraction Wizard screen loads.
  4. Type C:LCLD9 at the prompt and click Next.
    The Extraction Wizard begins unzipping files.
  5. Click Finish to complete the file extraction.
  6. Connect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  7. Click to select Specific Location and then click Next.
  8. Under the Include this location in the search field section, click Browse and click to select C:LCLD9.
  9. Select driver LCLD9.inf, click Next,and then click Finish.
  10. Right-click My Computer andthenclick Properties.
    The System Properties window appears.
  11. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  12. Complete the installation by verifying the driver is now appearing correctly in device manager under Ports (COM & LPT) and note the port number.

Internet Reinstall

Logic Controls Usb Devices Driver Updater

To reinstall the pole display USB virtual COM port drivers from the Internet, perform the following steps:

Logic Controls Usb Devices Driver Windows 7

  1. Download the driver file at: www.logiccontrols.com/web/utilities/ld9w2kcom.zip.
  2. Choose Open from the File Download prompt.
  3. Click File, and then click to select Extract All.
    The Extraction Wizard screen loads.
  4. Type C:LCLD9 at the prompt and click Next.
    The Extraction Wizard begins unzipping files.
  5. Click Finish to complete the file extraction.
  6. Remove the USB pole display cable from the USB port.
  7. Right-click any unknown items, and then click to select Remove. (Figure 2)
    NOTE: If there are any references to Line Display LD9900, right-click the listing, and then click Uninstall.
  8. Repeat step 2 until there are no unknown devices in Device Manager.
  9. Right-click any unknown items, and click to select Remove.
  10. Repeat this step until there are no unknown devices left.
  11. Reconnect the USB pole display cable to the USB port.
    The operating system detects the device and the Found New Hardware wizard appears.
  12. Choose Specific Location and click Next.
  13. Under the Include this location in the search field section, click Browse and click to select C:LCLD9.
  14. Select driver LD9COM.inf, click Next, and then click Finish.
  15. Right-click My Computer andthenclick Properties.
    The System Properties screen loads.
  16. Select the Hardware tab and click Device Manager.
    The Device Manager window appears.
  17. Complete the installation by verifying the driver is now appearing correctly in device manager under Ports (COM & LPT), and note the port number.

Logic Controls Usb Devices Drivers